Search results for "polymer composite"
showing 10 items of 31 documents
The effects of water absorption and salt fog exposure on agglomerated cork compressive response
2022
The replacement of synthetic foams with agglomerated cork in sandwich composites can meet the increasing environmental concerns. Its peculiar morphology and chemical composition lead to outstanding dimensional recovery that endorsed a broad investigation of its compressive behavior. The knowledge of neat material response is fundamental to obtain a reliable design dataset, but it is necessary to consider all the environmental factors (water, moisture and sunlight) that significantly modify material mechanical properties. In view of this, the present work investigates the effect of distilled and seawater absorption and salt fog exposure on the compressive behavior of two agglomerated corks w…
Basalt Fibre Composite with Carbon Nanomodified Epoxy Matrix under Hydrothermal Ageing
2021
This work aimed to investigate the effect of hybrid carbon nanofillers (e.g., carbon nanotubes/carbon nanofibers in the ratio 1:1 by mass) over the electrical and flexural properties for an epoxy matrix and corresponding basalt fibre reinforcing composite (BFRC) subjected to full-year seasonal water absorption. Hydrothermal ageing was performed by full immersion of the tested materials into distilled water according to the following model conditions (seasons). The mechanical properties were measured in three-point bending mode before environmental ageing and after each season. Upon environmental ageing, the relative change of flexural strength and elastic modulus of the epoxy and NC was wit…
Green composites: A brief review
2011
The rising concern towards environmental issues and, on the other hand, the need for more versatile polymer-based materials has led to increasing interest about polymer composites filled with natural-organic fillers, i.e. fillers coming from renewable sources and biodegradable. The composites, usually referred to as "green", can find several industrial applications. On the other hand, some problems exist, such as worse processability and reduction of the ductility. The use of adhesion promoters, additives or chemical modification of the filler can help in overcoming many of these limitations. These composites can be further environment-friendly when the polymer matrix is biodegradable and c…
Dynamic Mechanical Behavior Analysis of Flax/Jute Fiber-Reinforced Composites under Salt-Fog Spray Environment
2020
Over the last decades, natural fiber-reinforced polymer composites (NFRPs) gained great attention in several engineering fields thanks to the reduction of the environmental impact and the end-of-life cost disposal. Unfortunately, the use of NFRPs is limited, mainly due to their weak resistance against humid environments. Since limited literature is available about the evolution of the dynamic mechanical response of NFRPs under aggressive environments, this paper aims to investigate the damping properties of flax, jute and flax/jute epoxy composites exposed to salt-fog up to 60 days. Furthermore, sodium bicarbonate fiber treatment was performed to improve the composites&rsquo
Glass-basalt/epoxy hybrid composites for marine applications
2011
Abstract The aim of this work is to evaluate the influence of uniaxial basalt fabric layers on the mechanical performances of a glass mat/epoxy composite used for marine applications. Polymer composites, reinforced by glass mat (GFRP), and hybrid ones, reinforced by glass mat and unidirectional basalt fabric, have been produced by vacuum bagging technique. Three points bending and tensile tests have been carried out in order to evaluate the effect of number and position of basalt layers on the mechanical properties of the investigated structures. The experimental tests have showed that the presence of two external layers of basalt involves the highest increase in mechanical properties of hy…
Durability assessment of basalt fiber polymer as reinforcement to expanded clay concrete in harsh environment
2021
Basalt fiber-reinforced polymer composites are receiving considerable attention as they represent a low-cost green source of raw materials. In most cases, fiber-reinforced polymer composites face harsh environments, such as chloride ions in coastal marine environments or cold regions with salt deicing. The resistance of fiber-reinforced polymers subjected to the above environments is critical for the safe design and application of such composites. This research aims to develop a framework to investigate the durability properties of the lightweight expanded clay basalt fiber polymer reinforced concrete exposed to the NaCl environment. The specified quantity of concrete structural elements wa…
Resistance of Conifer Needle Polyolefin Composites (CNPCs) Against Biodecomposition Caused by Fungi
2017
This study describes the resistance of composites filled with conifer needles to biodecomposition processes caused by a single strain of Aspergillus niger as well as by a consortium of microorganisms present in the compost substrates (forest or spent mushroom composts). The impact of various types of conifer needles on the growth of A. niger was studied to determine whether the filler can show the fungistatic effect. The changes in chemical composition of the composites surfaces were examined using attenuated total reflectance Fourier transform infrared spectroscopy (FTIR/ATR). The results showed that the fungistatic effects of conifer needles polyolefin composites (CNPCs) were associated w…
The Reinforcement Effect of Strain Gauges Embedded in Low Modulus Materials
2013
The reinforcement effect of electrical resistance strain gauges is well-described in the literature, especially for strain gauges installed on surface. This paper considers the local reinforcement effect of strain gauges embedded within low Young modulus materials. In particular, by using a simple theoretical model, already used for strain gauges installed on the surface, it proposes a simple formula that allows the user to evaluate the local reinforcement effect of a generic strain gauge embedded on plastics, polymer composites, etc. The theoretical analysis has been integrated by numerical and experimental analyses, which confirmed the reliability of the proposed model.
Effect of aggregation of a dispersed rigid filler on the elastic characteristics of a polymer composite
1986
We proposed a method for describing the effective elastic characteristics of a polymer composite with a rigid aggregating filler. An important feature of such a medium is the variable coupling of the inclusion phase in relation to its volume content. A change in the degree of coupling of the filler is accounted for by introducing an additional parameter. We examined a method of determining the coupling parameter from the results of statistical modeling of the geometry of the medium. Using the example of a calcite-HDPE composite, we showed that aggregation has a significant effect on the dependence of the elastic modulus on the volume content of filler; satisfactory agreement was obtained be…
Robustness of Empirical Vibration Correlation Techniques for Predicting the Instability of Unstiffened Cylindrical Composite Shells in Axial Compress…
2020
Thin-walled carbon fiber reinforced plastic (CFRP) shells are increasingly used in aerospace industry. Such shells are prone to the loss of stability under compressive loads. Furthermore, the instability onset of monocoque shells exhibits a pronounced imperfection sensitivity. The vibration correlation technique (VCT) is being developed as a nondestructive test method for evaluation of the buckling load of the shells. In this study, accuracy and robustness of an existing and a modified VCT method are evaluated. With this aim, more than 20 thin-walled unstiffened CFRP shells have been produced and tested. The results obtained suggest that the vibration response under loads exceeding 0.25 of …